Schedule An Appointment

 

 

They are making a number of good observations on the subject of How to Install a Bathtub Yourself overall in the content just below.

Mounting a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably tough job. If the old bathtub is readily accessible, the task can relocate easily; if you need to open up a wall surface to eliminate the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the brand-new one. Make certain you have certified on your own for the work as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is much better to think about employing one prior to you begin. Possibilities are you might require a professional plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your shower room if you have currently purchased a brand-new bathtub and do not need to change the setup of your previous supply of water pipes.
Your devices and also material checklist must comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you need to change old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be fairly problematic because of the limited accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before going on to fit the new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making certain that the washing machines are in location in between the tap and the sink. Secure the tap in place with the producer offered backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The former type ought to be connected to the tap ends first, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Setting up the Tub

Utilizing the two wooden boards under its feet, place the bathtub in the called for placement. The wood boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the tub until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Activate the water as well as inspect all joints as well as new pipework for leaks and also tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait till the tub has been made use of a minimum of once as this will certainly resolve it into its final placement.

 

 

Getting ready for the Installment

First of all, the supporting structure supplied with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.

 

 

Tiling Around the Bathtub

In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall in between the bathroom and also the tiling, causing difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water-proof adhesive as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you really like reading about A Step-by-Step Guide to Installing a Bathtub? Post feedback down below. We will be glad to know your feelings about this article. We are looking forward to see you back again in the near future. If you please take the opportunity to share this blog if you enjoyed reading it. Thanks a lot for your time. Don't hesitate to visit our blog back soon.

Book Services